for Split Ring Heart
1227 CR 1760 E
Greenup Illinois USA 62428-3016
Needlecraft Magazine published in the first half of the 20th century in Augusta, Maine was one of many publications designed for women. It featured everything from recipes to home remedies, practical linens and clothes repairs to delicate laces. The earliest issue that I have is from 1912. It continued in publication under that name until about 1933 when the name was changed to Needlecraft Home Arts Magazine. It last appeared in the early 1940's under the name of Home Arts Magazine. It had monthly issues and specialty publications.
This is the earliest issue that I have that actually shows tatting on the cover.
These designs are by Clara Haase. Her name appears more than once in Needlecraft Magazine. I also believe that this same set of patterns was reprinted 48 years later in "Olde Time Needlework Patterns and Designs: Exquisite Designs and Patterns Out of the Glorious Past " in the March 1973 issue. And, now, 89 years after they first appeared, the patterns are still ever fresh.
R = Ring CH = Chain clr = close ring rw = reverse work dnrw = do not reverse work - = picot + = join
*RA 6 - 6 - 5 - 2 - 5 clr dnrw. CH 8 + (join to first picot of ring)
RB 5 - 5 - 5 - 5 clr dnrw. Continue CH 8 + (join to first picot of previous ring) 2 - 2 - 2 - 1 + (join to second picot of same ring) 1 - 2 - 2 - 2 - + (join to third picot of same ring) 8 + (join to base of same ring) CH 8 + (join to second picot of initial ring.)
RA 6 - 6 - 5 - 2 - 5 clr dnrw. CH 8 + (join to first picot of ring)
CH 9 + (join to last picot of chain around initial ring A) 6 - 6 - 9 + (join to first picot of ring B at the same spot where this chain began) CH 8 + (join to second picot of ring )
Repeat from * for length desired and finish off ends.
At end of row make last chain which has no inner ring a split ring and exit through the middle picot and begin the return pass of all tatted chains.
CH 8 - 8 + (join to previous row) 8 - 8 and repeat.
Using two shuttles tat a round center ring of 7 picots separated by 3 ds. Close ring and climb out with a mock picot into the next round.
Using shuttle one tat onion ring R 8 - 8 clr dnrw. Rotate ring slightly to begin the outer onion ring more easily.
Outer onion ring R 11 + (onion ring join to inner ring) small picot 11 clr. Anchor thread with a join to the base of the inner ring.
Bring shuttle thread to the back of the center ring and make shuttle lock join to the next two picots. Once secured to the second picot, repeat onion ring set.
Continue around for a total of four sets of onion rings.
Bring shuttle thread to the back of the center ring and make shuttle lock join to the next free picot. Once secured to the picot, begin next all chain round.
CH 8 - 6 + (join to the picot on the next outer onion ring,) 1 - 6 - 8 slj to the next free standing picot on center ring.
The last round of chain work may be attached separately, or make the last chain of the previous round a split chain.
The set of two chains at the corner of the motif are all CH 6 - 6 + the single chain at the sides are CH 7 - 7 +
If tatting this pattern using the onion ring technique, the special onion ring joins must be used!
*R 7 - 7 - 7 - 7 clr dnrw
CH 8 + (join to first picot of ring) dnrw
Using shuttle 2 throw off a floating ring off this chain.
R 7 - 1 - 1 - 7 clr dnrw
CH 8 + (join to second picot of first ring) dnrw
*Repeat from * for desired length.
For the last ring in the row; tat the upper chain with floating ring first. Then make the last ring a split ring which exits at the third picot into the next round.
The finishing round of the pattern is all chains.
CH 9 - 9 + (join to the third picots of the rings) and repeat to the end.
Begin this straight chain with a starter picot.
CH 8 - repeat for desired length. At end turn and work back the opposite direction. CH 8 - 8 + (join to picot of straight chain); when you reach the beginning of the chain join to the starter picot with an 8 ds split chain. This brings you into the last pass. CH 7 + (join to next freestanding picot) 5, using picot gauge create 9 picots, 5 + (join to next picot) continue to end and finish off ends.
Additional patterns from this set will be studied soon. I would love to have a new model of this lace to illustrate this pattern. If you would like to submit photo please send jpg to AKTATTER@aol.com. To view the photos more easily, open them in a new window or right click and save to your computer graphics program.
Tatting is NOT a lost art! Visit the Learning Center